重投影
参数
坐标系
如果要素具有坐标系,则该坐标系将用作重投影的源,并且忽略此变换器的源坐标系参数。
如果要素没有源坐标系,并且源坐标系参数未设置,则转换器仅将要素的坐标系设置为目标坐标系,并且要素的坐标保持不变。
注:如果源坐标系不是固定的,并且可能在不同的特征之间发生变化,并且特征本身已经用产生它们的读取器的坐标系进行了标记,那么仍然可以使用单个重投影器。在这种情况下,源坐标系和目标坐标系都可以设置为相同的值-目标坐标系-并且可以实现所需的行为。
光栅参数
这个插值类型仅影响光栅数据。单元值是内插的,以便将光栅更改为指定的大小。
- 最近的邻居速度最快,但产生的图像质量最差。
- 双线性提供速度和质量的合理平衡。
- Bicubic速度最慢但产生的图像质量最好。
- 平均4和平均16有类似于双线性对于数字光栅(如DEM)非常有用。
这个单元格大小applies only to raster features.
- 拉伸单元格:将调整光栅的单元格大小,以保持重投影光栅中的行数和列数与输入光栅中的行数和列数相同。
- 方形单元格:行数和列数以及间距将改变,以保持大致相同的单元格接地面积,并形成水平和垂直单元格大小相等的方形单元格。
- 保存单元格:就像方形单元格option, this option will change both the number of rows and columns and the spacing to maintain cell ground area, but will also try to preserve the original cell aspect ratio, taking into account any warping caused by the reprojection.
动态坐标系
If the destination coordinate system is specified as "_AZMEA_" or "_AZMED_", each input feature is reprojected to either an equal area or equal distance projection appropriate for that feature, respectively. In general, this causes a new coordinate system to be defined for each input feature.
每个特征都会记住它所具有的特定等距或等面积坐标系,并且可以安全地重新投影回正常(非动态)坐标系。亚搏在线
例如:
- LL-WGS84中有一个表示地球上某个点的输入特征(正常纬度/经度)。
- 这个point is reprojected to _AZMED_ via a Reprojector with source LL-WGS84 and destination _AZMED_.
- 这个x and y coordinates of the point are extracted into x1, y1.
- 设置x2=x1+1000,y2=y1。
- Add a vertex to the point to make the line (x1,y1) -> (x2,y2).
- 通过带有源和目标LL-WGS84的重投射器重投射回LL-WGS84。
注:注意来源是忽略在这里。我们只是选择了阿兹迈德来帮助记忆发生了什么。有时人们更喜欢将源和目标都设置为LL-WGS84。
- 现在我们把我们的点改成了一条线,从原来的点向东延伸1公里,以纬度/长度表示。
Dynamic coordinate systems have the following limitation:
•不考虑Z,因此面积或距离最好保留为0米椭球高度的几何体。
例子
Usage Notes
- 此转换器同时处理光栅和矢量数据。
- 此转换器不受光栅标注栏和调色板选择的影响。
编辑变压器参数
使用一组菜单选项,可以通过引用工作空间中的其他元素来指定转换器参数。更高级的功能,如高级编辑器和算术编辑器,也可以在一些变压器。要访问这些选项的菜单,请单击在适用参数旁边。有关详细信息,请参阅变压器参数菜单选项.
变压器类别
Search FME Knowledge Center
Search for samples and information about this transformer on theFME知识中心.
标签Keywords: pointcloud